Shijiazhuang Laiye Import& Export Trading Co., Ltd. is one of the leading manufacturers and suppliers of we6 solenoid directional valve 35 mpa in China, also supports customized service. If you're going to wholesale high quality we6 solenoid directional valve 35 mpa made in China, welcome to get pricelist from our factory.
Technical Parameters
| Parameter | Value |
|---|---|
| Specification | 6 |
| Max Working Pressure, P A B Ports | 35 MPa |
| Max Working Pressure, T Port | 21 MPa |
| Max Flow | 80 L/min |
| Working Voltage, DC | 12/24 |
| Working Voltage, AC | 110/220 |
| Model Number | 4WE6E / J / H / G / D / Y |
| Brand | Onederful® Hydraulic or OEM/ODM |
Why the T Port Rating Matters
The WE6 Solenoid Directional Valve 35 MPa is rated at 35 MPa on P, A, and B. That's the main working pressure. But the T port - the return line - is rated at 21 MPa. That's a big difference, and it's not a typo. It reflects the fact that the return line doesn't normally see the same pressure as the main circuit.
In a simple system, return oil flows back to tank at low pressure. But in more complex systems, multiple actuators may share a common return line. If several functions are returning oil at the same time, back pressure can build up. If that back pressure approaches 21 MPa, the spool may not shift reliably. It might stick, or it might not return to center properly.
So when you're matching this valve to your system, check the return line design. Make sure the back pressure stays well below 21 MPa. If it doesn't, you'll need to adjust the system or choose a different valve.
Flow Capacity and Sizing
The maximum flow is 80 L/min. That's the highest flow the valve is designed to handle. If your pump delivers more than 80 L/min, the valve will become a restriction. You'll see pressure drop, heat, and slower actuator response. If your pump delivers less than 80 L/min, the valve will still work, but you may not be using its full capacity.
Matching the valve to your pump is straightforward. Check your pump's maximum flow and compare it to 80 L/min. If you're close, this valve is a good fit. If you're significantly higher, you need a larger valve. If you're significantly lower, you might be able to use a smaller, more economical valve.
Voltage Options: DC and AC
The WE6 offers two voltage families: DC 12/24 and AC 110/220. The coil can be replaced if the control voltage changes, but it's easier to specify the correct voltage at the time of order.
DC coils are common in mobile equipment, battery-powered systems, and applications where the power source is 12 or 24 volts. AC coils are more common in industrial settings where line voltage is available. Both are available for this valve.
Make sure the coil voltage matches your control circuit. A mismatch means the valve won't shift. If you're unsure which voltage you need, check the power supply or contact us for guidance.
Understanding Model Numbers
The model numbers 4WE6E, 4WE6J, 4WE6H, 4WE6G, 4WE6D, and 4WE6Y indicate different spool functions or control configurations. The letter after "4WE6" typically denotes the center condition or spool type. Different letters correspond to different flow paths in the neutral position - closed center, open center, float center, etc.
The exact function of each model number should be confirmed with the supplier before ordering. It's not something to guess, because the wrong spool type can affect how the machine behaves when the valve is in neutral. For example, a closed-center spool will hold the actuator in position, while an open-center spool will let the pump unload. The choice depends on your circuit requirements.
Installation Best Practices
Mounting the valve is straightforward, but a few details matter. The mounting surface should be flat and clean. If it's not, tightening the bolts can distort the body and cause the spool to bind. Tighten the bolts evenly, in a cross pattern. If you have a torque wrench, use it.
Before connecting the hydraulic lines, flush them. Debris left in the piping will find its way into the valve and cause problems. After installation, cycle the valve through its positions several times to purge air from the circuit. Then check for leaks at the port connections and at the mounting face.
Keep the hydraulic oil clean. Contamination is the leading cause of spool sticking and seal wear. Replace filters on schedule. Check the oil viscosity and temperature periodically to make sure they stay within the operating limits for your system.
Maintenance and Troubleshooting
The WE6 doesn't need much day-to-day attention, but a few checks can catch problems early.
If the valve doesn't shift, check the coil voltage first. Make sure the solenoid is receiving power. If the coil is energised but the valve doesn't respond, the spool may be stuck. In that case, check oil cleanliness and inspect the spool.
If the valve shifts slowly or hesitates, the oil may be too thick or too contaminated. Check the oil temperature and viscosity. If the oil is outside the recommended range, adjust the system or change the oil.
External leaks are usually easy to spot. A small weep at the mounting face or port connections often means a damaged O-ring or uneven bolt torque. Re-torque the bolts evenly and replace any damaged seals.
For more serious issues, contact the supplier. Provide the valve model number and a description of the problem. That helps speed up diagnosis.
Ordering Information
When ordering the WE6 Solenoid Directional Valve 35 MPa, specify the following:
Specification: 6
Voltage: DC 12/24 or AC 110/220
Model number: 4WE6E, 4WE6J, 4WE6H, 4WE6G, 4WE6D, or 4WE6Y
Brand preference: Onederful® Hydraulic or OEM/ODM
OEM/ODM service is available. Provide your drawing or requirements, and the valve can be configured accordingly.
About the Manufacturer
Shijiazhuang Laiye Import & Export Trading Co., Ltd. belongs to Hebei Onederful® Hydraulic Technology Co., Ltd. The company was founded in 1988 and has more than 35 years of experience in pressure valve components. It employs over 200 people and ships more than 10,000 containers of specialized products each year to customers in more than 20 countries. ISO9002 certification was obtained in 2000.
Every batch goes through at least 10 inspection procedures before shipment. The warranty on the WE6 is 12 months against B/L date. Small pieces are packed in carton boxes. Large pieces are packed in export-grade plywood cases. Shipping can be by sea, air, or international express. Payment methods include PayPal, Western Union, Money Gram, and T/T transfer.
For full company information, visit About Us.
FAQ
Q: How do I choose the right model number among 4WE6E, J, H, G, D, and Y?
A: The letter after "4WE6" indicates the spool function - specifically, how the ports are connected when the valve is in neutral. Different letters give different flow paths: closed center, open center, float center, etc. Tell us what your circuit should do when the valve is not energised, and we'll recommend the matching model number.
Q: Why is the T port rated at 21 MPa while P, A, and B are rated at 35 MPa?
A: The T port is the return line. It isn't designed to handle the full working pressure. In most systems, return oil flows back to tank at low pressure. But if your return line carries back pressure from other functions, keep it below 21 MPa. Otherwise the spool may not shift reliably.
Q: What flow rate can the WE6 handle?
A: The maximum flow is 80 L/min. If your pump delivers more than that, the valve will become a restriction, causing pressure drop and heat. If it delivers less, the valve will still work, but you may not be using its full capacity.
Q: Should I choose DC 12/24 or AC 110/220?
A: It depends on your control circuit. DC coils are common in mobile equipment and battery-powered systems. AC coils are more common in industrial settings with line voltage. The coil can be replaced later if needed, but it's easier to specify the correct voltage at the time of order.
Q: Can I use this valve in a system with a return line back pressure above 21 MPa?
A: No. The T port limit is 21 MPa. If your return line back pressure regularly exceeds that, you need a different valve or a modified circuit design. Check the back pressure before installing the valve.
Hot Tags: we6 solenoid directional valve 35 mpa, China we6 solenoid directional valve 35 mpa, manufacturers, suppliers, factory, dc valve in hydraulic, direction flow control valve, directional control valve spool, hydraulic directional, hydraulic pilot operated directional control valve, sectional hydraulic control valves
